Complete Custom Closet: How to Make the Most of Every Space by Chris Gleason

By Chris Gleason

Most likely the worst examples of expertise, store defense, and end paintings. i can't suggest this ebook to an individual.

Show description

Read Online or Download Complete Custom Closet: How to Make the Most of Every Space (Popular Woodworking) PDF

Best woodworking books

405 Woodworking Patterns

The Southwestern component of this enjoyable trend booklet features a gecko welcome peg rack, adobe bookends, cactus shelf, coyote change plate conceal, and extra.

DIY For Dummies

Discovering a wood worker who does caliber work—at an inexpensive cost and in a well timed fashion—can be a true problem. For little jobs you could spend extra time trying to find a chippie than you'll doing the task your self, should you in basic terms had a few easy instruments and carpentry talents. through the years, the power to address small carpentry jobs can prevent loads of funds.

Building Snowshoes

* * INSCRIBED AND SIGNED by way of the writer ON identify web page * * delicate hide with plastic comb binding, illustrated with b/w images and drawings, a hundred pages. third revision. conceal has gentle put on to edges - usually to information of corners and flippantly dirty. textual content is unmarked. photos to be had. USPS affirmation used on all U.

Additional resources for Complete Custom Closet: How to Make the Most of Every Space (Popular Woodworking)

Example text

NGLE DOVETAIL ANGLE APPROXIMATE SLOPE (degrees) 7 8 9 11 14 60 1:8 1:7 1:6 1:5 1:4 CHAPTER TWO Dowel Joints • Use a dowel diameter that’s between one-third and one-half the stock thickness (for example use a 1 ⁄ 4", 5 ⁄ 16" or 3 ⁄ 8"-diameter dowel for 3 ⁄ 4"thick stock). • When boring dowel holes, add 1 ⁄ 16" clearance at each end to allow for excess glue. • When using dowels to help align edge-to-edge joints, space the dowels 8" to 12" apart. Lap Joints • When the mating parts are the same thickness, the lap should be onehalf the stock thickness.

When nailing near the end of a board, drill pilot holes to prevent the stock from splitting. The pilot hole diameter should be about 75 percent of the nail diameter and bored to a depth of about two-thirds the nail length. Screw Joints • About two-thirds of the screw (or the entire thread length) should enter the mating piece. • When both parts are about the same thickness, the screw length should be 1 ⁄ 8" to 1 ⁄ 4" less than the combined thicknesses of the parts. Example: Use a 15 ⁄ 8"-long screw when joining a 3 ⁄ 4"-thick piece to a 1"-thick piece.

Can) bottom end of Minwax Wood Finish (1 ⁄ 2 pint can) bottom end of Borden’s condensed milk (12 oz. can) bottom end of Minwax Wood Finish (1 pint can) bottom end of Folger’s coffee (12 oz. can) bottom end of Butcher’s Wax (16 oz. can) compact disc bottom end of Cabot’s Wood Stain 3⁄ 8 3⁄4 7⁄ 8 7 ⁄ 16 1 13 ⁄ 8 11 ⁄ 2 1⁄ 2 15 ⁄ 8 23 ⁄ 4 13 ⁄ 16 13 ⁄ 8 27 ⁄ 8 17 ⁄ 16 3 11 ⁄ 2 33 ⁄ 8 4 41 ⁄ 4 43 ⁄ 4 63 ⁄ 4 111 ⁄ 16 2 21 ⁄ 8 23 ⁄ 8 33 ⁄ 8 11 ⁄ 16 3⁄4 WOODWORKING MATH 53 chapter two furniture design 54 CHAPTER ONE Common Woodworking Joints Butt (end to end) Butt (edge to edge) Through Dado Stopped Dado Groove Rabbet Rabbet and Dado Cross Lap FURNITURE DESIGN 55 End Lap T-Lap 56 T-Bridle Tongue and Groove Flat Miter Edge Miter Rabbet Miter End Miter CHAPTER TWO Lap Miter Biscuit (end to edge) Biscuit Round Mortise and Tenon Stub Mortise and Tenon Blind Mortise and Tenon Haunched Mortise and Tenon Through Mortise and Tenon FURNITURE DESIGN 57 Pinned Mortise and Tenon Open Mortise and Tenon 58 Finger or Box Joint Through Dovetail Blind Dovetail Half-Blind Dovetail Half-Dovetailed Dado Dovetailed Dado CHAPTER TWO Keyed Dovetail Half-Lap Dovetailed Half-Lap Dowel (end to edge) Doweled Miter Spline (end to edge) Spline (edge to edge) Splined Miter Miter With Spline Key FURNITURE DESIGN 59 General Rules for Joinery Design A number of general rules, or rules of thumb, apply to the design of woodworking joints.

Download PDF sample

Rated 4.85 of 5 – based on 4 votes